MasonryDefender All Purpose Concrete Brick & Stone Sealant is a high performance, penetrating silane/siloxane blended water repellent that provides long lasting water repellency on concrete and masonry surfaces. This water-based product is a breathable, non-film forming, concrete sealer exterior water repellent that will not alter surface color or appearance. It protects most vertical and horizontal, exterior, above-grade concrete surfaces. It can be used on residential driveways, patios, sidewalks, brick walls, stone walls, concrete walls, chimneys, or any other bare masonry or concrete surfaces. It protects most masonry or concrete surfaces including concrete, brick, stone, cultured stone, sandstone, limestone, granite and more. Natural substrate color and surface textures are unaffected with little or no gloss created. Slight darkening may occur on dense surfaces. Testing is recommended before treating any surface to ensure desired results. This product is designed to protect and waterproof and seal concrete and masonry surfaces once they have been properly cleaned with MasonryDefender All Purpose Masonry & Concrete Cleaner. MasonryDefender All Purpose Concrete, Brick & Stone Sealer This concrete sealer can cover a range from 90-150 sq. ft. per gallon depending on surface porosity. Before applying to your concrete, please make sure that the surface is completely clean and allowed to dry for at least 6 hours. Available in both a 1 gallon and a 2.5 gallon container. Unlike heavy 5 gallon containers, the 2.5 gallon containers are easier to lift, and easy to pour. This product isn't just for concrete. It can be used as an all purpose water repellent and sealer for any bare masonry, concrete, or natural stone surface. Properly Protects Your Concrete, Brick or Stone Surfaces Use the MasonryDefender All Purpose Concrete, Brick & Stone Sealer to fully protect your concrete and masonry surface as well as brightening the appearance and enhancing your curb appeal. Protects against cracking and pitting that is caused by moisture that seeps into the concrete over time. It also has a salt guard that protects against de-icing salts and chemicals. After the solution is applied, water will now bead instead of seeping into your driveway causing more damage. Once cured, you'll notice that your driveway, sidewalk or patio will dry much sooner than your neighbors as water isn't able to penetrate into your concrete or masonry surfaces. No longer waste your time power washing your driveway for hours. Stay fully protected for up to 5 years on vertical surfaces. How To Apply The Concrete, Brick & Stone Sealer Make sure that the surface temperature is a minimum of 40°F and a maximum of 100°F for three hours following application. Once your surface is free and clear of any dirt and debris, use a low pressure pump-up garden sprayer to spray a thin, even layer. The use of a sprayer will allow you to evenly apply the product. For vertical surfaces, start at the bottom and work your way towards the top, applying a flood coat so that the sealer runs down approximately 6" from where you're spraying. The surface should remain wet for 2-3 minutes before final absorption. Apply a second coat within a few minutes of the first. On horizontal surfaces, avoid puddling or ponding; brush or broom to spread material until the sealer thoroughly penetrates the surface. Surface will be dry in 2-6 hours, depending on temperature and humidity. Allow 24 hours before driving on surface. Concrete Driveway Sealer Low Gloss Patio Paver Sealer Interior/Exterior Brick Sealer Stamped Concrete Sealer Gloss Wet Look Patio Paver Sealer All Purpose Masonry & Concrete Cleaner Add to Cart Add to Cart Add to Cart Add to Cart Add to Cart Add to Cart Customer Reviews 4.4 out of 5 stars 822 4.5 out of 5 stars 457 4.4 out of 5 stars 404 4.4 out of 5 stars 408 4.2 out of 5 stars 308 3.8 out of 5 stars 96 Price $37.49$37.49 $44.99$44.99 $37.49$37.49 $45.99$45.99 $53.99$53.99 $37.99$37.99
